| Index of Tables |
| Preface |
| Introduction / Section 1： |
| General Principles of Electric Motor Control / Unit 1： |
| Fractional and Integral Horsepower Manual Motor Starters / Unit 2： |
| Magnetic Line Voltage Starters / Unit 3： |
| Circuit Layout, Connections, and Symbols / Section 2： |
| Symbols / Unit 4： |
| Interpretation and Application of Simple Wiring and Elementary Diagrams / Unit 5： |
| Control Pilot Devices / Section 3： |
| Push Buttons and Control Stations / Unit 6： |
| Relays / Unit 7： |
| Contactors / Unit 8： |
| Timing Relays / Unit 9： |
| Pressure Switches and Regulators / Unit 10： |
| Float Switches / Unit 11： |
| Flow Switches / Unit 12： |
| Limit Switches and Proximity Control / Unit 13： |
| Phase Failure Relays / Unit 14： |
| Solenoid Valves / Unit 15： |
| Temperature Switches / Unit 16： |
| Basic Control Circuits / Section 4： |
| Two-Wire Controls / Unit 17： |
| Three-Wire and Separate Controls / Unit 18： |
| Hand-Off Automatic Controls / Unit 19： |
| Multiple Push-Button Stations / Unit 20： |
| Interlocking Methods for Reversing Control / Unit 21： |
| Sequence Control / Unit 22： |
| Jogging (Inching) Control Circuits / Unit 23： |
| Time-Delay, Low-Voltage Release Relay / Unit 24： |
| AC Reduced Voltage Starters / Section 5： |
| The Motor and Starting Methods / Unit 25： |
| Primary Resistor-Type Starters / Unit 26： |
| Autotransformer Starters / Unit 27： |
| Part Winding Motor Starters / Unit 28： |
| Automatic Starters for Star-Delta Motors / Unit 29： |
| AC Solid-State Reduced Voltage Controller / Unit 30： |
| Three-Phase, Multispeed Controllers / Section 6： |
| Controllers for Two-Speed, Two-Winding (Separate Winding) Motors / Unit 31： |
| Two-Speed, One-Winding (Consequent Pole) Motor Controller / Unit 32： |
| Four-Speed, Two-Winding (Consequent Pole) Motor Controller / Unit 33： |
| Wound Rotor (Slip Ring) Motor Controllers / Section 7： |
| Wound Rotor Motors and Manual Speed Control / Unit 34： |
| Push-Button Speed Selection / Unit 35： |
| Automatic Acceleration for Wound Rotor Motors / Unit 36： |
| Automatic Speed Control for Wound Rotor Motors / Unit 37： |
| Solid-State Adjustable Speed Controller for AC Wound Rotor Motors / Unit 38： |
| Synchronous Motor Controls / Section 8： |
| Synchronous Motor Operation / Unit 39： |
| Push-Button Synchronizing / Unit 40： |
| Timed Semiautomatic Synchronizing / Unit 41： |
| Synchronous Automatic Motor Starter / Unit 42： |
| Direct-Current Controllers / Section 9： |
| About DC Motors / Unit 43： |
| Use of Reduced Voltage for Starting / Unit 44： |
| Across-the-Line Starting / Unit 45： |
| Compensating and Definite Time Control Starting / Unit 46： |
| Solid-State Adjustable Speed Control / Unit 47： |
| Methods of Deceleration / Section 10： |
| Plugging / Unit 48： |
| Electric Brakes / Unit 49： |
| Dynamic and Regenerative Braking / Unit 50： |
| Electric and Electronic Braking / Unit 51： |
| Motor Drives / Section 11： |
| Direct Drives and Pulley Drives / Unit 52： |
| Gear Motors / Unit 53： |
| Variable-Frequency Mechanical Drives / Unit 54： |
| AC Adjustable Frequency Drives / Unit 55： |
| Magnetic Clutch and Magnetic Drive / Unit 56： |
| DC Variable Speed Control--Motor Drives / Unit 57： |
| Programmable and Motion Control / Unit 58： |
| Motor Start-Up and Troubleshooting Basics / Unit 59： |
| Motor Types and Line Diagrams / Appendix A： |
| Power Supplies / Appendix B： |
| Glossary |
| Index |
| Index of Tables |
| Preface |
| Introduction / Section 1： |
図書
